Skip to content

First time DIYer – what kit should I buy for a crawl space?

Table of Contents

Home Community Forum DIY Spray Foam First time DIYer – what kit should I buy for a crawl space?

  • This topic is empty.
Viewing 8 posts - 1 through 8 (of 8 total)
  • Author
    Posts
  • #2690

    I have a 1200 sq ft crawl space I want to insulate. Never used spray foam before. Looking at the 2-component kits – Froth-Pak seems popular. Any advice for a first-timer?

    #2691
    Amy Chambers
    Member

    Froth-Pak is solid for DIY. For a crawl space that size get the 650 board foot kit, maybe two. Do not forget safety gear – respirator, safety glasses, and gloves are non-negotiable.

    #2692

    I did my crawl space last year with a similar kit. Biggest tip: warm the tanks up to 70-75 degrees before use. Cold temperatures kill your yield and mixing ratio.

    #2693
    Bob Tremblay
    Member

    Practice on cardboard first. The learning curve is real. Your first few passes will likely be uneven. Do multiple thin passes rather than one thick one.

    #2694

    What about temperature – my crawl space is around 55 degrees. Is that too cold?

    #2695
    Amy Chambers
    Member

    55F is borderline. Ideally substrate should be above 60F. Run a space heater in there for a few hours before you start. The tanks should also be 70-80F for proper mixing.

    #2696

    Seal any standing water or condensation first. Spray foam does not adhere well to wet surfaces. And make sure you have ventilation – those fumes are serious.

    #2697

    Got it – will rent a dehumidifier and run a heater the day before. Ordered the Froth-Pak 650 two-pack. Will report back with results!

Viewing 8 posts - 1 through 8 (of 8 total)
  • You must be logged in to reply to this topic.

Uncategorized

Uncategorized

Uncategorized

REVIEWS YOU CAN RELY ON

Our Network

Spray foam insulation can crank up the performance of your homes—if you do it right. Check out our daily posts on the Foam Insulation and the Foam Insulation Market. We review each company and relay the information directly to you. Join our mailing list and have them sent directly to your email each and every day.
If you would like to know more about polyurea or spray foam, we recommend visiting ArmorThane
Mike T. (TX) posted in Contractor Talk: "Best temp settings for 2lb foam in summer heat"New article: "Spray Foam R-Value: The Complete Guide" — Read it nowSarah K. (OH) rated a contractor 5 stars in ClevelandWebinar: Cold Climate Installations — June 18 at 2PM EDT — Register Free28 new members joined this week!Texas Chapter Meetup: June 24 in Dallas — RSVP nowFoamPro_Dave replied: "Graco vs Gusmer after 8 years — my verdict"Mike T. (TX) posted in Contractor Talk: "Best temp settings for 2lb foam in summer heat"New article: "Spray Foam R-Value: The Complete Guide" — Read it nowSarah K. (OH) rated a contractor 5 stars in ClevelandWebinar: Cold Climate Installations — June 18 at 2PM EDT — Register Free28 new members joined this week!Texas Chapter Meetup: June 24 in Dallas — RSVP nowFoamPro_Dave replied: "Graco vs Gusmer after 8 years — my verdict"
👥 14,247 Members💬 312 Active This Week📰 131 Articles4.9/5 Rating📅 4 Events This Month
LIVE Community
Mike T. (TX) posted in Contractor Talk
2 min ago
Sarah K. (OH) asked in Ask An Expert
9 min ago
FoamPro_Dave replied in Equipment and Rigs
15 min ago
NewContractor2025 joined the community
32 min ago
Linda G. (OR) posted in Green Building
48 min ago
Join 14,247 Members Free